Skip to page content
USDA Forest Service
  
Treesearch

Research & Development Treesearch

 
Treesearch Home
About Treesearch
Contact Us
Research & Development
Forest Products Lab
International Institute of Tropical Forestry
Northern
Pacific Northwest
Pacific Southwest
Rocky Mountain
Southern Research Station
Help
 

Science.gov - We Participate


USA.gov  Government Made Easy


Global Forest Information Service

US Forest Service
P.O. Box 96090
Washington, D.C.
20090-6090

(202) 205-8333

You are here: Home / Search / Publication Information
Bookmark and Share

Publication Information

View PDF (1.3 MB bytes)

Title: Integrated Protection Against Lyctid Beetle Infestations Part II. - Laboratory Dip-Diffusion Treatment of Unseasoned Banak (Virola spp.) Lumber with Boron Compounds

Author: Williams, Lonnie H.; Mauldin, Joe K.;

Date: 1985

Source: Res. Note SO-313. New Orleans, LA: U.S. Department of Agriculture, Forest Service, Southern Forest Experiment Station. 8 p.

Publication Series: Research Note (RN)

Description: A manufacturer of conventional moulding wanted a method that would prevent lyctid beetle damage to banak (Virola spp.) wood throughout the period from initial cutting in Brazil until final mouldings were in use. Because complete penetration of wood may be obtained, unseasoned banak wood was treated by dip-diffusion with disodium octaborate tetrahydrate Na2B8O13*4H2O as TIM-BOR®)l or boric acid (H3BO3) to determine the dip time, solution temperature, and diffusion storage period that would provide optimum treatment of wood. Visual observations also were made of inhibition of mold growth during diffusion storage as a result of using < 3.0 percent concentrations of sodium pentachlorophenate (NaPCP) with TIM-BOR® and copper-8-quinolinolate (as PQ-57®) with treating solutions of boric acid. Recommendations for commercial trial treatments of freshly sawn banak and similar woods in the Brazilian Amazon are: 1. Treatment solution. In situations where most boards are 38 mm (1.5 inch) thick, a 25 to 30 percent boric acid equivalent solution of sodium borate (such as TIM-BOR®) should be used, with 4 to 5 kg (8 to 11 lb) of NaPCP added for mold prevention in each 1000 liters (264 gal) of solution. 2. Because heated solutions yield better results and steam heat is often readily available, the treatment solution should be maintained at 50° to 60°C (122° to 140°F). 3. Dip time.--A minimum time of 1 minute is suggested. 4. Diffusion storage.--Boards should be placed on piling sticks immediately after dipping and stored under a roof or other cover for 1 week. 5. Other factors.--Low wood moisture caused by delay between sawing and treating or procedures used for piling treated lumber may affect the penetration of boron into wood and should be tested.

Publication Notes:

  • We recommend that you also print this page and attach it to the printout of the article, to retain the full citation information.
  • This article was written and prepared by U.S. Government employees on official time, and is therefore in the public domain.
  • You may send email to pubrequest@fs.fed.us to request a hard copy of this publication. (Please specify exactly which publication you are requesting and your mailing address.)

XML: View XML

Citation:


Williams, Lonnie H.; Mauldin, Joe K. 1985. Integrated Protection Against Lyctid Beetle Infestations Part II. - Laboratory Dip-Diffusion Treatment of Unseasoned Banak (Virola spp.) Lumber with Boron Compounds. Res. Note SO-313. New Orleans, LA: U.S. Department of Agriculture, Forest Service, Southern Forest Experiment Station. 8 p.

 


 [ Get Acrobat ]  Get the latest version of the Adobe Acrobat reader or Acrobat Reader for Windows with Search and Accessibility

USDA logo which links to the department's national site. Forest Service logo which links to the agency's national site.