Skip to page content
USDA Forest Service
  
Treesearch

Research & Development Treesearch

 
Treesearch Home
About Treesearch
Contact Us
Research & Development
Forest Products Lab
International Institute of Tropical Forestry
Northern
Pacific Northwest
Pacific Southwest
Rocky Mountain
Southern Research Station
Help
 

Science.gov - We Participate


USA.gov  Government Made Easy


Global Forest Information Service

US Forest Service
P.O. Box 96090
Washington, D.C.
20090-6090

(202) 205-8333

You are here: Home / Search / Publication Information
Bookmark and Share

Publication Information

View PDF (293 KB bytes)

Title: Efficient utilization of red maple lumber in glued-laminated timber beams

Author: Janowiak, J. J.; Manbeck, H. B.; Hernandez, R.; Moody, R. C.; Blankenhorn, P. R.; Labosky, P.;

Date:

Source: (Research paper FPL ; RP-541):23 p. : ill. ; 28 cm.

Publication Series: Research Paper (RP)

Description: The feasibility of utilizing cant-sawn hardwood lumber, which would not usually be desired for furniture manufacture, was studied for the manufacture of structural glued-laminated (glulam) timber. Two red maple beam combinations were evaluated: (1) a glulam combination designed with E-rated lumber in 25 percent of the outer laminations (top and bottom) and No. 3 grade lumber in 50 percent of the center laminations and (2) a wide-width glulam combination with laminations made from nominal 2- by 4- and 2- by 6-in. No. 2 grade lumber laid edge-to-edge having staggered end joints (termed 2 by 4/2 by 6 glulam combination). Test results of 42 red maple glulam beams showed that it was feasible to develop structural glulam timber from cant-sawn lumber. The glulam combinations made from E-rated lumber exceeded the target design bending stress of 2,400 lb/in2 and met the target modulus of elasticity (MOE) of 1.8 * 106 lb/in2. In addition, the 2 by 4/2 by 6 glulam combination exceeded published design stresses for vertically laminated bending strength, MOE in both the horizontally and vertically laminated orientations, and horizontal shear stress in the vertically laminated orientation. Based on the results of the 2 by 4/2 by 6 glulam combination, it was determined that edge gluing the laminations to form wide-width lumber is not required to achieve targeted strength and stiffness levels. Data analysis showed that ASTM D3737 procedures developed for softwood species accurately predict beam stiffness and provide conservative bending and horizontal shear strength estimates for red maple glulam beams. Also, it was shown that results from ASTM D143 shear-block tests could be used to accurately predict horizontal shear strength of 2 by 4 and 2 by 6 red maple glulam beams.

Keywords: Laminated wood, Lumber, Beams, Bending strength, Modulus of elasticity, Hardwoods, Glulam, Cant sawing, E-rated lumber

Publication Notes:

  • We recommend that you also print this page and attach it to the printout of the article, to retain the full citation information.
  • This article was written and prepared by U.S. Government employees on official time, and is therefore in the public domain.

XML: View XML

Citation:


Janowiak, J. J.; Manbeck, H. B.; Hernandez, R.; Moody, R. C.; Blankenhorn, P. R.; Labosky, P. Efficient utilization of red maple lumber in glued-laminated timber beams. (Research paper FPL ; RP-541):23 p. : ill. ; 28 cm.

 


 [ Get Acrobat ]  Get the latest version of the Adobe Acrobat reader or Acrobat Reader for Windows with Search and Accessibility

USDA logo which links to the department's national site. Forest Service logo which links to the agency's national site.